资质认证
- IEC 60745-2-8:2003+AMD1:2008 CSV
- Hand-held motor-operated electric tools - Safety - Part 2-8: Particular requirements for shears and nibblers
- 2008-08-12
- IEC 60745-2-4:2002+AMD1:2008 CSV
- Hand-held motor-operated electric tools - Safety - Part 2-4: Particular requirements for sanders and polishers other than disk type
- 2008-08-12
- IEC 61290-3:2008
- Optical amplifiers - Test methods - Part 3: Noise figure parameters
- 2008-08-12
- IEC 61649:2008
- Weibull analysis
- 2008-08-12
- ISO/IEC 14165-122:2005/AMD1:2008
- Amendment 1 - Information technology - Fibre channel - Part 122: Arbitrated loop-2 (FC-AL-2)
- 2008-08-12
- IEC 61291-6-1:2008
- Optical amplifiers - Part 6-1: Interfaces - Command set
- 2008-08-12
- IEC 60745-2-21:2002+AMD1:2008 CSV
- Hand-held motor-operated electric tools - Safety - Part 2-21: Particular requirements for drain cleaners
- 2008-08-12
- IEC 60364-4-43:2008
- Low-voltage electrical installations - Part 4-43: Protection for safety - Protection against overcurrent
- 2008-08-12
- IEC 61157:2007/COR1:2008
- Corrigendum 1 - Standard means for the reporting of the acoustic output of medical diagnostic ultrasonic equipment
- 2008-08-11
- IEC 62127-2:2007/COR1:2008
- Corrigendum 1 - Ultrasonics - Hydrophones - Part 2: Calibration for ultrasonic fields up to 40 MHz
- 2008-08-11
- IEC 60745-2-6:2003+AMD1:2006+AMD2:2008 CSV
- Hand-held motor-operated electric tools - Safety - Part 2-6: Particular requirements for hammers
- 2008-08-11
- IEC 61467:2008
- Insulators for overhead lines - Insulator strings and sets for lines with a nominal voltage greater than 1 000 V - AC power arc tests
- 2008-08-11
- IEC 60825-1:2007/COR1:2008
- Corrigendum 1 - Safety of laser products - Part 1: Equipment classification and requirements
- 2008-08-11
- IEC 62127-1:2007/COR1:2008
- Corrigendum 1 - Ultrasonics - Hydrophones - Part 1: Measurement and characterization of medical ultrasonic fields up to 40 MHz
- 2008-08-11
- IEC 62424:2008
- Representation of process control engineering - Requests in P&I diagrams and data exchange between P&ID tools and PCE-CAE tools
- 2008-08-11
- IEC 62424:2008
- Representation of process control engineering - Requests in P&I diagrams and data exchange between P&ID tools and PCE-CAE tools
- 2008-08-11
- ISO/IEC 23000-7:2008
- Information technology -- Multimedia application format (MPEG-A) -- Part 7: Open access application format
- 2008-08-10
- ISO/IEC 23000-9:2008
- Information technology -- Multimedia application format (MPEG-A) -- Part 9: Digital Multimedia Broadcasting application format
- 2008-08-10
- ISO/IEC 23000-9:2008
- Information technology — Multimedia application format (MPEG-A) — Part 9: Digital Multimedia Broadcasting application format
- 2008-08-10
- ISO/IEC 23000-7:2008
- Information technology — Multimedia application format (MPEG-A) — Part 7: Open access application format
- 2008-08-10
